Chamberlain Home Security System PIRV400R User Manual

®
Models PIRV400R  
Wireless Pedestrian & Vehicle Sensor with Voice  
AOSV  
Wireless Office Alert Add-On Sensor  
Overview  
The PIR Motion Sensor only works with  
Chamberlain's Wireless Pedestrian & Vehicle Alert  
with Voice (Model RWV400R) and Office Alert  
(Model CWV1000). The PIR Motion Sensor can be  
used to monitor motion up to 30' away and can  
transmit a signal up to 1000' away from the Base  
Station (not included). The Passive Infra-Red sensor  
detects movement of people and vehicles, while  
allowing small animals to pass through undetected.  
The PIR Motion Sensor has a built-in microphone and  
speaker that allows for communication between the  
Base Station and the Sensor. When the PIR Motion  
Sensor detects movement a signal is sent to the base  
station which alerts the homeowner with sounds and  
lights. The Alert can also remotely control a low  
voltage electrical device near the PIR Motion Sensor  
like a light or a camera (See Advanced Features).  
To prevent possible SERIOUS INJURY or DEATH from  
electrocution, outputs are suitable ONLY for controlling low  
voltage devices, 24V max, ac or dc.  
Intercom Feature: When PIR Motion Sensor has  
detected motion, the Base Station will allow you to  
listen through the PIR Motion Sensor for 10 seconds.  
If you wish to talk to the person on the other end,  
hold down the Talk button and speak, releasing it to  
hear.  
Volume: Pressing the Volume button repeatedly will  
cycle through volume levels.  
Mute: To temporarily mute Base Station, hold the  
Volume and Talk buttons down for three seconds.  
The Base Station will reactivate after one hour, or by  
pressing the Talk button.  
Carton Inventory  
Remote Button: If there is an accessory device  
connected to the relay on the PIR Motion Sensor, it  
can be activated by pressing the Remote button  
within 30 seconds of the signal from the alert buzzer.  
Swivel Bushing  
Switch #1:  
OFF  
ON  
Buzzer Off  
Buzzer On (Default)  
Mounting Plate  
Passive Infra-Red (PIR)  
Motion Sensor  
OFF  
ON  
1
2
Switch #2:  
OFF  
ON  
Long Buzz  
Short Buzz (Default)  
Operation & Features  
Battery: The AA Alkaline batteries (not provided) will  
last up to 2 years depending on use (Lithium batteries  
recommended for colder environments). If PIR Motion  
Sensor batteries are low Base Station will emit three  
high-pitch beeps every ten minutes. If Base Station  
batteries are low it will emit two high-pitch beeps.  
Base Station  
(not provided)  
PIR Motion  
Sensor  
PIR Sensor/Test Light  
Volume Button  
Talk  
(Power - On)  
Clear Memory: Press and hold the Learn button on  
the Base Station until 3 beeps are heard. If the PIR  
Motion Sensor signals while Learn button is pressed,  
repeat the procedure.  
Relay Output  
Contacts  
Remote  
Activation  
Button  
AC Adapter  
Learn  
Button  
Switch #1: Mute  
Switch #2: Tone  
Programming Additional PIR Motion Sensors:  
Each Base Station can learn the code of up to 8 PIR  
Motion Sensors, responding with multiple buzzes. To  
program additional PIR Motion Sensors see Step 6.  
Speaker  
On/Off: To turn Base Station OFF hold down the  
Volume button until a beep is heard and light goes  
out. To turn Base Station ON press the Talk button.  
1
 
Advanced Features  
Troubleshooting  
Both the PIR Motion Sensor and Base Station have  
relays which can activate other electrical devices. The  
accessory device will need a separate power supply.  
NOTE: Output switching capacity is low voltage (24V  
max, ac or dc).  
The Alert does not function.  
Check batteries in PIR Motion Sensor. Ensure Base  
Station has power. Ensure PIR Motion Sensor is  
programmed to Base Station.  
The Alert is not getting expected transmission  
range.  
Ensure Base Station antenna is vertical and keep PIR  
Motion Sensor away from trees and metal objects.  
Ensure Base Station is in clearest possible range of  
PIR Motion Sensor. The less objects between  
devices, the longer the range.  
Base Station: The relays can be  
used to activate louder alarm bells,  
lights, cameras, or other accessories.  
PIR Motion Sensor: The relays will  
only activate when the remote button  
is pressed on the Base Station. To  
prevent access to these relays flush  
mount the PIR Motion Sensor.  
Base Station is not very loud.  
Adjust the volume of speaker. An accessory such as  
a low voltage bell, buzzer or light can be attached to  
the relay switch. The accessory device will need  
separate power supply.  
NOTE: Output switching capacity is low voltage  
(24V max, ac or dc).  
Static and feedback is heard in Base Station.  
PIR Motion Sensor is too close to the Base Station.  
The PIR Motion Sensor is detecting motion only  
part of the time.  
To detect cars, it is best to mount PIR Motion Sensor  
at height of car’s motor and have it between ten and  
twenty feet from the road. Swivel sensor as needed.  
The Alert is giving false alarms.  
Check for moving tree branches or insects in sensor  
window. PIR sensor can also be triggered by light  
shining directly in sensor window, such as reflected  
sunlight, or motion in front of a light source.  
Base Station beeps every ten minutes.  
If there are two beeps the battery is low in the Base  
Station. Replace with AA Alkaline batteries or operate  
it with AC Adapter. If there are three beeps the battery  
is low in the PIR Motion Sensor. Replace with AA  
Alkaline batteries.  
3
 
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:  
1-800-528-9131  
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this  
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery.  
THERE ARE NO OTHER USER SERVICEABLE PARTS.  
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following  
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause undesired operation.  
© 2008, The Chamberlain Group Inc.  
All Rights Reserved  
114A3516C  
 

BenQ Computer Monitor GL2040AM User Manual
Black Box Switch 26615 User Manual
Black Decker Saw 5146961 02 User Manual
Black Decker Saw FS210LS User Manual
Bosch Power Tools Laser Level GPL4 User Manual
Bose Whiteboard Accessories PDF259774_00 User Manual
Briggs Stratton Portable Generator 030217 User Manual
Briggs Stratton Tiller 5055 6 HP User Manual
Canon Printer 830D User Manual
Chamberlain Garage Door Opener 3245CM User Manual