Bosch Appliances Security Camera NTC 265 PI User Manual

IP Camera 200 Series  
NTC-265-PI  
en Installation Manual  
 
IP Camera 200 Series  
Table of Contents | en  
3
Table of Contents  
Safety  
Safety precautions  
Important safety instructions  
FCC & ICES compliance  
UL certification  
Bosch notices  
Copyrights  
Introduction  
Features  
Unpacking  
Installation  
Assembly  
Mounting  
Network (and power) connector  
Power connection  
DC power connection  
I/O connector  
Audio connectors  
Camera set-up  
Camera positioning  
Resetting the camera  
Browser connection  
System requirements  
Establishing the connection  
Password protection in camera  
Protected network  
Troubleshooting  
Resolving problems  
Customer service  
Bosch Security Systems  
Installation Manual  
AM18-Q0610 | v1 | 2012.02  
 
4
en | Table of Contents  
IP Camera 200 Series  
Maintenance  
Repairs  
Transfer and disposal  
Technical Data  
Specifications  
Accessories  
AM18-Q0610 | v1 | 2012.02  
Installation Manual  
Bosch Security Systems  
 
IP Camera 200 Series  
Safety | en  
5
1
Safety  
1.1  
Safety precautions  
DANGER!  
High risk: This symbol indicates an imminently hazardous  
situation such as "Dangerous Voltage" inside the product.  
If not avoided, this will result in an electrical shock, serious  
bodily injury, or death.  
WARNING!  
Medium risk: Indicates a potentially hazardous situation.  
If not avoided, this could result in minor or moderate bodily  
injury.  
CAUTION!  
Low risk: Indicates a potentially hazardous situation.  
If not avoided, this could result in property damage or risk of  
damage to the device.  
Bosch Security Systems  
Installation Manual  
AM18-Q0610 | v1 | 2012.02  
 
   
6
en | Safety  
IP Camera 200 Series  
1.2  
Important safety instructions  
Read, follow, and retain for future reference all of the following  
safety instructions. Heed all warnings on the unit and in the  
operating instructions before operating the unit.  
1. Cleaning - Generally, using a dry cloth for cleaning is  
sufficient but a moist, fluff-free cloth or leather shammy  
may also be used. Do not use liquid cleaners or aerosol  
cleaners.  
2. Heat Sources - Do not install the unit near any heat  
sources such as radiators, heaters, stoves, or other  
equipment (including amplifiers) that produce heat.  
3. Water - Never spill liquid of any kind on the unit.  
4. Lightning - Take precautions to protect the unit from  
power and lightning surges.  
5. Controls adjustment - Adjust only those controls specified  
in the operating instructions. Improper adjustment of  
other controls may cause damage to the unit.  
6. Power sources - Operate the unit only from the type of  
power source indicated on the label.  
7. Servicing - Unless qualified, do not attempt to service this  
unit yourself. Refer all servicing to qualified service  
personnel.  
8. Replacement parts - Use only replacement parts specified  
by the manufacturer.  
9. Installation - Install in accordance with the manufacturer's  
instructions and in accordance with applicable local codes.  
10. Attachments, changes or modifications - Only use  
attachments/accessories specified by the manufacturer.  
Any change or modification of the equipment, not  
expressly approved by Bosch, could void the warranty or,  
in the case of an authorization agreement, authority to  
operate the equipment.  
AM18-Q0610 | v1 | 2012.02  
Installation Manual  
Bosch Security Systems  
 
 
IP Camera 200 Series  
Safety | en  
7
1.3  
FCC & ICES compliance  
FCC & ICES Information  
This equipment has been tested and found to comply with the  
limits for a Class B digital device, pursuant to part 15 of the  
FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference  
to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following  
measures:  
reorient or relocate the receiving antenna;  
increase the separation between the equipment and  
receiver;  
connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected;  
consult the dealer or an experienced radio/TV technician  
for help.  
This device complies with part 15 of the FCC Rules. Operation  
is subject to the following two conditions:  
1. this device may not cause harmful interference, and  
2. this device must accept any interference received,  
including interference that may cause undesired operation.  
Intentional or unintentional modifications, not expressly  
approved by the party responsible for compliance, shall not be  
made. Any such modifications could void the user's authority to  
operate the equipment. If necessary, the user should consult  
the dealer or an experienced radio/television technician for  
corrective action.  
Bosch Security Systems  
Installation Manual  
AM18-Q0610 | v1 | 2012.02  
 
 
8
en | Safety  
IP Camera 200 Series  
The user may find the following booklet, prepared by the  
Federal Communications Commission, helpful: How to Identify  
and Resolve Radio-TV Interference Problems. This booklet is  
available from the U.S. Government Printing Office,  
Washington, DC 20402, Stock No. 004-000-00345-4.  
1.4  
UL certification  
Disclaimer  
Underwriter Laboratories Inc. ("UL") has not tested the  
performance or reliability of the security or signaling aspects of  
this product. UL has only tested fire, shock and/or casualty  
hazards as outlined in UL's Standard(s) for Safety for Closed  
Circuit Television Equipment, UL 2044. UL Certification does not  
cover the performance or reliability of the security or signaling  
aspects of this product.  
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR  
CERTIFICATIONS WHATSOEVER REGARDING THE  
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR  
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.  
1.5  
Bosch notices  
Disposal - Your Bosch product was developed and  
manufactured with high-quality material and components that  
can be recycled and reused. This symbol means that  
electronic and electrical appliances, which have reached the  
end of their working life, must be collected and disposed of  
separately from household waste material. Separate collecting  
systems are usually in place for disused electronic and  
electrical products. Please dispose of these devices at an  
environmentally compatible recycling facility, per European  
Directive 2002/96/EC  
More information  
For more information please contact the nearest Bosch Security  
Systems location or visit www.boschsecurity.com  
AM18-Q0610 | v1 | 2012.02  
Installation Manual  
Bosch Security Systems  
 
   
IP Camera 200 Series  
Safety | en  
9
1.6  
Copyrights  
The firmware 4.1 uses the fonts "Adobe-Helvetica-Bold-R-  
Normal--24-240-75-75-P-138-ISO10646-1" and "Adobe-  
Helvetica-Bold-R-Normal--12-120-75-75-P-70-ISO10646-1"under  
the following copyright:  
Copyright 1984-1989, 1994 Adobe Systems Incorporated.  
Copyright 1988, 1994 Digital Equipment Corporation.  
Permission to use, copy, modify, distribute and sell this  
software and its documentation for any purpose and without  
fee is hereby granted, provided that the above copyright  
notices appear in all copies and that both those copyright  
notices and this permission notice appear in supporting  
documentation, and that the names of Adobe Systems and  
Digital Equipment Corporation not be used in advertising or  
publicity pertaining to distribution of the software without  
specific, written prior permission.  
This software is based in part on the work of the Independent  
JPEG Group.  
Bosch Security Systems  
Installation Manual  
AM18-Q0610 | v1 | 2012.02  
 
 
10 en | Introduction  
IP Camera 200 Series  
2
Introduction  
2.1  
Features  
The Bosch NTC-265-PI 720p infrared IP bullet camera is a ready-  
to-use, robust network camera. This camera offers a cost  
effective solution for a broad range of applications. The robust  
aluminum camera body is IP66 rated, offering water and dust  
proofing for demanding environments. The built-in active  
infrared illuminator ensures effective vision under extreme low-  
light conditions. The camera easily integrates with the Bosch  
DVR 700 Series recorder and can also be used with an iSCSI  
server connected via the network to store long-term recordings.  
Features include:  
High performance active infrared illuminator inside the  
camera for extreme low-light environments  
Tri-streaming: Two H.264 streams and one M-JPEG stream  
HD 720p Progressive scan for sharp images of moving  
objects  
Robust IP66-rated camera design  
Two-way audio and audio alarm  
Power over Ethernet (IEEE 802.3af compliant)  
Tamper and motion detection  
Conforms to the ONVIF standard for wide compatibility  
AM18-Q0610 | v1 | 2012.02  
Installation Manual  
Bosch Security Systems  
 
   
IP Camera 200 Series  
Introduction | en 11  
2.2  
Unpacking  
Unpack carefully and handle the equipment with care.  
The packaging contains:  
IP camera with lens  
Torx screwdriver  
Camera fixing screw kit  
Installation paper sticker  
Quick installation guide  
CD ROM  
Bosch Video Client  
Documentation  
Tools  
If equipment has been damaged during shipment, repack it in  
the original packaging and notify the shipping agent or supplier.  
WARNING!  
Installation should only be performed by qualified service  
personnel in accordance with the National Electrical Code or  
applicable local codes.  
CAUTION!  
The camera module is a sensitive device and must be handled  
carefully.  
Bosch Security Systems  
Installation Manual  
AM18-Q0610 | v1 | 2012.02  
 
 
12 en | Installation  
IP Camera 200 Series  
3
Installation  
3.1  
Assembly  
The sun hood on the camera/housing unit can be adjusted.  
1. Adjustment screw  
2. Sun hood  
To adjust the sun hood proceed as follows:  
1. Using the special screwdriver bit supplied, loosen the top  
adjustment screw (1) in the housing.  
2. Slide the sun hood (2) to the desired position.  
3. Tighten the top adjustment screw (1).  
AM18-Q0610 | v1 | 2012.02  
Installation Manual  
Bosch Security Systems  
 
   
IP Camera 200 Series  
Installation | en 13  
3.2  
Mounting  
x4  
mm  
6
Ø
M4 (Ø3.3 mm)  
x4  
Figure 3.1 Mounting the camera  
To mount the camera to a wall or ceiling:  
1. Stick the supplied installation paper sticker to the surface  
taking care to orientate it correctly.  
2. Drill four holes with a diameter of 6 mm.  
3. Insert the supplied plugs into the holes.  
4. Attach the camera and base unit securly to the surface  
using the two supplied M4 screws.  
CAUTION!  
Do not point the camera/lens into direct sunlight as this may  
damage the sensors.  
Bosch Security Systems  
Installation Manual  
AM18-Q0610 | v1 | 2012.02  
 
 
14 en | Installation  
IP Camera 200 Series  
3.3  
Network (and power) connector  
RJ45  
Ethernet (PoE)  
Figure 3.2 Network connection  
Connect the camera to a 10/100 Base-T network.  
Use a shielded UTP Category 5e cable with RJ45  
connectors.  
Power can be supplied to the camera via the Ethernet  
cable compliant with the Power-over-Ethernet  
(IEEE 802.3af) standard.  
CAUTION!  
This equipment is only to be connected to PoE networks  
without routing to outside plant.  
AM18-Q0610 | v1 | 2012.02  
Installation Manual  
Bosch Security Systems  
 
 
IP Camera 200 Series  
Installation | en 15  
3.4  
Power connection  
The camera can accept power from both the DC12V power  
input and the Ethernet input at the same time. You can remove  
either one of the power sources without interrupting camera  
operation.  
3.4.1  
DC power connection  
5 mm  
(0.2 in)  
22AWG  
12 VDC  
Figure 3.3 DC power connection  
Connect power from a 12 VDC class 2 power supply as follows:  
1. Use AWG22 wire; cut back 5 mm (0.2 in) of insulation.  
2. Remove the 2-pole connector from the camera cable tree.  
3. Loosen the screws and insert the wires.  
4. Tighten the screws and reconnect the 2-pole connector to  
the power connector of the camera cable tree.  
Bosch Security Systems  
Installation Manual  
AM18-Q0610 | v1 | 2012.02  
 
   
16 en | Installation  
IP Camera 200 Series  
3.5  
I/O connector  
5 mm  
(0.2 in)  
In: AWG30  
Out: AWG20  
Figure 3.4 I/O connector pins  
Function  
Wire  
Color  
Grey  
Relay out  
AWG20  
AWG20  
AWG30  
AWG30  
Red  
Alarm input  
Orange  
Brown  
Cut back 5 mm (0.2 in) of insulation.  
Relay switching capability: Max. voltage 24 VAC or 24 VDC.  
Max. 1 A continuous, 12 VA.  
Alarm in: Short or +5 VDC activation.  
Alarm input configurable as active low or active high.  
AM18-Q0610 | v1 | 2012.02  
Installation Manual  
Bosch Security Systems  
 
 
IP Camera 200 Series  
Installation | en 17  
3.6  
Audio connectors  
Line - L  
GND  
Line - R  
Figure 3.5 Audio connectors  
Connect audio devices to the Line In and Line Out connectors.  
Line in: 9 kOhm typical, 200 mVrms  
Line out: 16 Ohm minimum 200 mVrms (earphone  
compatible)  
Bosch Security Systems  
Installation Manual  
AM18-Q0610 | v1 | 2012.02  
 
 
18 en | Installation  
IP Camera 200 Series  
3.7  
Camera set-up  
To help set up the camera, connect a monitor to the BNC  
connector of the camera cable tree. This connector provides a  
composite video signal (with sync) for installation purposes  
only.  
AM18-Q0610 | v1 | 2012.02  
Installation Manual  
Bosch Security Systems  
 
 
IP Camera 200 Series  
Installation | en 19  
3.7.1  
Camera positioning  
The camera position can be adjusted along three axes. When  
adjusting ensure that the picture display on the monitor is level.  
Set the camera to the desired position using the supplied Torx  
screwdriver:  
1. For vertical adjustment (1), loosen the locking screw and  
move the camera housing to the desired angle. Tighten the  
screw.  
2. For horizontal adjustment (2), loosen the locking screw  
and rotate the camera housing around the base. Tighten  
the screw.  
3. To obtain a horizontal horizon (3), rotate the camera body  
as necessary to align the picture shown on the monitor.  
Bosch Security Systems  
Installation Manual  
AM18-Q0610 | v1 | 2012.02  
 
 
20 en | Installation  
IP Camera 200 Series  
3.8  
Resetting the camera  
If the camera cannot be connected because the IP address has  
changed, short circuit the reset connector for approximately  
7 seconds to recall the factory default values. The factory  
default IP address is 192.168.0.1  
AM18-Q0610 | v1 | 2012.02  
Installation Manual  
Bosch Security Systems  
 
 
IP Camera 200 Series  
Browser connection | en 21  
4
Browser connection  
A computer with Microsoft Internet Explorer can be used to  
receive live images from the camera, control cameras, and  
replay stored sequences. The camera is configured over the  
network using a browser or via the Bosch Video Client  
(supplied with the product).  
4.1  
System requirements  
Microsoft Internet Explorer version 7.0 or higher  
Monitor: resolution at least 1024 × 768 pixels, 16 or 32 bit  
color depth  
Intranet or Internet network access  
The Web browser must be configured to enable Cookies to be  
set from the IP address of the unit.  
In Windows Vista, deactivate protected mode on the Security  
tab under Internet Options.  
To play back live video images, an appropriate ActiveX must be  
installed on the computer. If necessary, the required software  
and controls can be installed from the product disk provided.  
a. Insert the disk into the optical drive of the computer.  
If the disk does not start automatically, open the root  
directory of the disk in Windows Explorer and double  
click BVC-installer.exe  
b. Follow the on-screen instructions.  
To get full support for recordings and snapshots, install the  
MPEG_ActiveX from the product disk to your computer.  
Bosch Security Systems  
Installation Manual  
AM18-Q0610 | v1 | 2012.02  
 
   
22 en | Browser connection  
IP Camera 200 Series  
4.2  
Establishing the connection  
The camera must be assigned a valid IP address to operate on  
your network. The default address pre-set at the factory is  
192.168.0.1  
1. Start the Web browser.  
2. Enter the IP address of the camera as the URL.  
Note:  
If the connection is not established, the maximum number of  
possible connections may already have been reached.  
Depending on the device and network configuration, up to 25  
web browsers, or 50 Bosch VMS connections are supported.  
4.2.1  
Password protection in camera  
A camera offers the option of limiting access across various  
authorization levels. If the camera is password-protected, a  
message to enter the password appears.  
1. Enter the user name and the associated password in the  
appropriate fields.  
2. Click OK. If the password is correct, the desired page is  
displayed.  
4.3  
Protected network  
If a RADIUS server is used for network access control (802.1x  
authentication), the camera must be configured first. To  
configure the camera for a Radius network, connect it directly  
to a PC via a crossed network cable and configure the two  
parameters, Identity and Password. Only after these have been  
configured can communication with the camera via the network  
occur.  
AM18-Q0610 | v1 | 2012.02  
Installation Manual  
Bosch Security Systems  
 
     
IP Camera 200 Series  
Troubleshooting | en 23  
5
Troubleshooting  
5.1  
Resolving problems  
The following table is intended to help identify the causes of  
malfunctions and correct them when possible.  
Malfunction  
Possible causes  
Solution  
No image  
Faulty cable connections. Check all cables, plugs,  
transmission to  
remote location.  
contacts and  
connections.  
No connection  
The unit's configuration.  
Faulty installation.  
Check all configuration  
parameters.  
established, no  
image transmission.  
Check all cables, plugs,  
contacts and  
connections.  
5.2  
Customer service  
If a fault cannot be resolved, please contact your supplier or  
system integrator, or contact Bosch Security Systems  
Customer Service directly.  
The Installer should write down all information regarding the  
unit so that it can be referenced for warranty or repair. The  
version numbers of the firmware and other status information  
can be seen when the unit starts or by opening the Service  
menu. Note down this information and the information found  
on the camera label before contacting customer service.  
Bosch Security Systems  
Installation Manual  
AM18-Q0610 | v1 | 2012.02  
 
     
24 en | Maintenance  
IP Camera 200 Series  
6
Maintenance  
6.1  
Repairs  
CAUTION!  
Never open the casing of the camera. The unit does not contain  
any user serviceable parts. Ensure that all maintenance or  
repair work is performed only by qualified personnel (electrical  
engineering or network technology specialists). If in doubt,  
contact your dealer's technical service center.  
6.1.1  
Transfer and disposal  
The camera should only be passed-on together with this  
installation guide. The unit contains environmentally hazardous  
materials that must be disposed of according to law. Defective  
or superfluous devices and parts should be disposed of  
professionally or taken to your local collection point for  
hazardous materials.  
AM18-Q0610 | v1 | 2012.02  
Installation Manual  
Bosch Security Systems  
 
     
IP Camera 200 Series  
Technical Data | en 25  
7
Technical Data  
7.1  
Specifications  
Input voltage  
+12 VDC or Power-over-Ethernet  
Power consumption  
Sensor type  
6.72 W (max)  
¼-inch CMOS  
1280 x 800  
Sensor pixels  
Sensitivity  
0.3 lx (IR off)  
0 lx (IR on)  
Video resolution  
720p, 480p, 240p  
Video compression  
H.264 MP 720p30;  
H.264 MP SD;  
H.264 BP+ (Baseline Profile Plus);  
M-JPEG  
Max. frame rate  
Night vision  
LED  
30 fps  
25 m (82 ft)  
32 LED high efficiency array, 850 nm  
Varifocal 2.7 to 9 mm, F1.2 to close, D/N switch  
BNC connector  
Lens type  
Analog video output  
Alarm Input  
Relay Out  
Short or 5 VDC activation  
Switch rating: Max. 1 A 24 VAC/VDC  
Line in jack connector  
Audio Input  
Audio Output  
Line out jack connector  
Bosch Security Systems  
Installation Manual  
AM18-Q0610 | v1 | 2012.02  
 
   
26 en | Technical Data  
IP Camera 200 Series  
Audio  
Two-way, full duplex  
communication  
Audio compression  
Unit Configuration  
Protocols  
G.711, L16, AAC (live and recording)  
Via web browser or PC surveillance software  
HTTP, HTTPs, SSL, TCP, UDP, ICMP,RTSP, RTP,  
Telnet, IGMPv2/v3, SMTP,SNTP, FTP, DHCP  
client, ARP, DNS,DDNS, NTP, SNMP, UPnP,  
802.1X, iSCSI  
Ethernet  
PoE  
10/100 Base-T, auto-sensing, half/full duplex,  
RJ45  
IEEE 802.3af compliant  
Dimensions  
(H x W x D)  
100 x 100 x 291 mm (3.94 x 3.94 x 11.46 in)  
Weight  
1.6 kg (3.53 lb) approx.  
IP66  
Ingress Protection  
Operating  
-20 ºC to +50 ºC (-4 ºF to +122 ºF)  
Temperature  
Storage  
-20 ºC to +70 ºC (-4 ºF to +158 ºF)  
Temperature  
Humidity  
Less than 90% relative humidity (non-condensing)  
7.1.1  
Accessories  
Contact a Bosch representative in your area for the latest  
available accessories or visit our website at  
AM18-Q0610 | v1 | 2012.02  
Installation Manual  
Bosch Security Systems  
 
 
 
Bosch Security Systems  
© Bosch Security Systems, 2012  
 

Black Box Computer Accessories Cable Length Meter User Manual
Black Decker Pole Saw PSL12 User Manual
Blanco Indoor Furnishings 157 138 User Manual
Bosch Appliances Home Security System VIP X2 User Manual
Bushnell Binoculars 11 8338 User Manual
Carrier Home Security System TSTATCCSEN01 User Manual
Casio Cash Register TE 3000S User Manual
Casio Watch 1813 User Manual
Casio Watch MA1009 EA User Manual
Chicago Electric Saw 44829 User Manual