Bosch Appliances Home Security System VIP X1 XF E User Manual

VIP X1 XF E  
VIP-X1XF-E  
en Quick Installation Guide  
 
VIP X1 XF E  
Table of Contents | en  
3
Table of Contents  
1
2
3
Parts included  
Unpacking  
4
Installation  
8
4.1  
4.2  
4.3  
Mounting the frame  
5
Connection  
10  
10  
11  
12  
13  
14  
5.1  
5.2  
5.3  
5.4  
5.5  
Connecting the camera and audio  
Creating a serial connection  
Alarm and relay connections  
Establishing the network connection  
Connecting the power supply  
6
Assigning an IP address  
15  
Bosch Sicherheitssysteme GmbH  
Quick Installation Guide  
F.01U.269.645 | V2 | 2012.06  
 
4
en | About this Quick Installation Guide  
VIP X1 XF E  
1
About this Quick Installation Guide  
This Quick Installation Guide applies to all variants of the  
VIP X1 XF E.  
WARNING!  
You should always make yourself familiar with the required  
safety measures (see Safety document enclosed).  
Only operate the VIP X1 XF E in combination with an LPS/NEC  
Class 2 power supply unit with limited output.  
This Quick Installation Guide only describes the basic  
procedure for installing a VIP X1 XF E and cannot replace the  
complete manual.  
For further detailed information, please see the extensive  
online Help for the VIP X1 XF E.  
This Quick Installation Guide, the Installation and Operating  
Manual and the current firmware package are available in  
F.01U.269.645 | V2 | 2012.06  
Quick Installation Guide  
Bosch Sicherheitssysteme GmbH  
 
 
VIP X1 XF E  
Parts included | en  
5
2
Parts included  
1 VIP X1 XF E network video server  
1 terminal block  
4 self-adhesive elastic bumpers  
1 wall-mounting panel  
2 screws  
2 wall plugs  
1 Quick Installation Guide  
1 Safety Hints  
Bosch Sicherheitssysteme GmbH  
Quick Installation Guide  
F.01U.269.645 | V2 | 2012.06  
 
 
6
en | Unpacking  
VIP X1 XF E  
3
Unpacking  
Check that the delivery is complete and in perfect  
condition.  
Arrange for the unit to be checked by  
Bosch Security Systems if you find any damage.  
F.01U.269.645 | V2 | 2012.06  
Quick Installation Guide  
Bosch Sicherheitssysteme GmbH  
 
 
VIP X1 XF E  
Installation | en  
7
4
Installation  
4.1  
Preparing for wall-mounting  
You can secure the VIP X1 XF E to any load-bearing wall using  
the wall-mounting panel, in either a vertical or a horizontal  
position.  
CAUTION!  
If mounting the unit in a vertical position, you will need to use  
the lower plastic frame and then place the unit onto the frame  
from above. If mounting the unit in a horizontal position, you  
can use either of the two frames.  
Bosch Sicherheitssysteme GmbH  
Quick Installation Guide  
F.01U.269.645 | V2 | 2012.06  
 
   
8
en | Installation  
VIP X1 XF E  
4.2  
Mounting the frame  
CAUTION!  
The mounting location must be able to reliably hold the unit.  
The load-bearing capacity must be adequate for four times the  
weight of the unit.  
Lift the plastic frame on one side of the housing and  
carefully remove it from the unit.  
Screw the plastic frame in the required position together  
with the wall-mounting panel.  
Check that the plastic frame is secure.  
F.01U.269.645 | V2 | 2012.06  
Quick Installation Guide  
Bosch Sicherheitssysteme GmbH  
 
 
VIP X1 XF E  
Installation | en  
9
4.3  
Placing the unit in the frame  
Place the unit on the wall-mounting panel, with the panel  
positioned between the housing and the second plastic  
frame.  
Slide the unit into the plastic frame until you feel it lock  
securely into place.  
Finally, check that the unit is securely attached in the  
installation location.  
Bosch Sicherheitssysteme GmbH  
Quick Installation Guide  
F.01U.269.645 | V2 | 2012.06  
 
 
10 en | Connection  
VIP X1 XF E  
5
Connection  
5.1  
Connecting the camera and audio  
CAUTION!  
Please observe the following specifications:  
Line In: 9 kOhm typ., 5.5 Vp-p max.  
Line Out: 16 Ohm min., 3 Vp-p max.  
Connect the camera to the socket VIDEO IN.  
Use the LINE IN/OUT socket for audio line connections.  
F.01U.269.645 | V2 | 2012.06  
Quick Installation Guide  
Bosch Sicherheitssysteme GmbH  
 
   
VIP X1 XF E  
Connection | en 11  
5.2  
Creating a serial connection  
CTS  
RXD  
RTS  
TXD  
V I P X 1 X F  
R
TXD  
GND  
12  
V
D
C
GND  
RT  
LINK  
S
AC  
T
ETH  
CAUTION!  
Please observe the labeling on the orange socket of the  
VIP X1 XF E.  
If you require a serial connection to the VIP X1 XF E,  
connect the relevant cables to the terminal block.  
Connect the terminal block to the orange socket on the  
VIP X1 XF E.  
Bosch Sicherheitssysteme GmbH  
Quick Installation Guide  
F.01U.269.645 | V2 | 2012.06  
 
 
12 en | Connection  
VIP X1 XF E  
5.3  
Alarm and relay connections  
Alarm In  
IN  
R
GND  
R
V I P X 1 X F  
R
TXD  
GND  
1
2
V
DC  
GND  
RT  
LINK  
S
AC  
T
ETH  
CAUTION!  
Please observe the labeling on the orange socket of the  
VIP X1 XF E.  
Please observe the following specifications for the relay  
contact: max. 30 V  
(SELV), 200 mA  
p-p  
Connect the alarm switch to the appropriate terminals.  
Connect the switch connection to the appropriate  
terminals.  
F.01U.269.645 | V2 | 2012.06  
Quick Installation Guide  
Bosch Sicherheitssysteme GmbH  
 
 
VIP X1 XF E  
Connection | en 13  
5.4  
Establishing the network connection  
V I P X 1 X F  
R
TXD  
GND  
12  
V
D
C
GND  
RT  
LINK  
S
AC  
T
ETH  
UTP Cat 5 RJ45  
Connect the VIP X1 XF E to the network via the ETH  
socket.  
Bosch Sicherheitssysteme GmbH  
Quick Installation Guide  
F.01U.269.645 | V2 | 2012.06  
 
 
14 en | Connection  
VIP X1 XF E  
5.5  
Connecting the power supply  
V I P X 1 X F  
R
TXD  
GND  
1
2
V
DC  
GND  
RT  
LINK  
S
AC  
T
ETH  
CAUTION!  
Only operate the VIP X1 XF E in combination with an LPS/NEC  
Class 2 power supply unit that has limited output and meets  
the following specifications: 12 V output voltage, 0.30 A max.  
Connect the power supply unit to the 12V DC socket. The  
jack must fit a pin of 2 mm in diameter.  
Insert the power supply unit plug into a suitable socket.  
F.01U.269.645 | V2 | 2012.06  
Quick Installation Guide  
Bosch Sicherheitssysteme GmbH  
 
 
VIP X1 XF E  
Assigning an IP address | en 15  
6
Assigning an IP address  
NOTICE!  
Before you can operate the unit within your network, it must  
have a valid IP address for your network and a compatible  
subnet mask.  
If you have not already done so, install the Video Client  
program from the download area on our website.  
Start Video Client.  
Click  
to start Configuration Manager. The system  
automatically searches the network for compatible units.  
When the unit is displayed in the list, Configuration  
Wizard starts automatically. If not, select Configuration  
Wizard... from the Tools menu.  
Follow the instructions given in the Configuration Wizard  
window.  
Bosch Sicherheitssysteme GmbH  
Quick Installation Guide  
F.01U.269.645 | V2 | 2012.06  
 
 
16 en | Assigning an IP address  
VIP X1 XF E  
F.01U.269.645 | V2 | 2012.06  
Quick Installation Guide  
Bosch Sicherheitssysteme GmbH  
 
 
Bosch Sicherheitssysteme GmbH  
Robert-Bosch-Ring 5  
85630 Grasbrunn  
Germany  
© Bosch Sicherheitssysteme GmbH, 2012  
 

Black Box Breast Pump ICI42C User Manual
Black Box Switch 4 x 1 and 8 x 1 VGA Switches with Audio User Manual
Blanco Indoor Furnishings 514 477 User Manual
Bogen Speaker ASUG1DK User Manual
Boston Acoustics Recording Equipment 1000 User Manual
Breville Convection Oven BOV500 User Manual
Briggs Stratton Motorized Awning 253400 User Manual
Bushnell Binoculars 26 4202 User Manual
Canon Fax Machine L280 User Manual
Chicago Electric Drill 45338 User Manual